3DX CHAT COMMANDS MANUAL

If you hold down LCTRL while dragging the handles, the gizmo will scale the object inР’В increments of a specified step size. When more than one object is selected, the gizmo will be hidden. Note: The volume scale gizmo only works when a single object is selected and that object has to have aР’В mesh attached to it. Holding down SHIFT before dragging will cause the scale to happen from the center of the object.Р’В This key can be modified from the gizmo's inspector. When you drag,theР’В size and position of the object will be affected. Dragging one of them will scale along the corresponding object local axis. The gizmo is composed of 6 drag handles which can be dragged to scale the object. Instead of using axes that can be dragged, you can use handles to resize an object.Р’В This in combination with the step snapping functionality can provide a muchР’В more intuitive scaling interface in some scenarios. The volume scale gizmo is another type of gizmo which allows you to perform object scaling, but itР’В works a bit differently than the standard scale gizmo. In order to use Step snapping, you have to keep the CTRL keyР’В pressed and then use the scale gizmo as you normally do (drag the axes or the multi-axis triangles orР’В press SHIFT to scale along all axes at once). For example, if the step value is set to 1, a scale operation will be performed only whenР’В the accumulated scale is >= 1. The scale gizmo supports Step snapping which allows you to scale in increments of a specified worldР’В unit amount. If you want to perform a scale operation along all axes at once, you have to keep the SHIFT keyР’В pressed and then drag the mouse around. Clicking on one of theseР’В triangles and than dragging the mouse, will perform a scale operation along 2 axes at once. Clicking on of these axes and dragging the mouse, will perform aР’В scale operation along the specified axis.Р”Р„s you can see in the image above, there are also 3 multi-axis triangles. The following image shows the scale gizmo: Note: Step snapping works only when you are using one of the 3 colored circles. In order to use Step snapping, you have to keepР’В the CTRL button pressed and then manipulate the gizmo as you normally do. Only when the accumulated rotation amount is >= 15. For example, if this step value is set to 15, a rotation is performed The rotation gizmo supports Step snapping which allows you to rotate in increments of a specified stepР’В value (expressed in units of degrees). If you click on a point on the imaginary sphere (not on any of the components that we have discussedР’В so far), you will be able to rotate around the camera right and up axes. Clicking on this circle and then dragging the mouse willР’В allow you to rotate around the camera view vector.

You can rotateР’В around a single axis by clicking on one of the circles and then start dragging the mouse.Р”Р„s you can see in the image above, there is also an outer circle (the one which encloses the rotationР’В sphere and which is also slightly bigger). The rotation gizmo has 3 colored circles that can be used to rotate around a single axis. The rotation gizmo allows you to rotate objects in the scene.Р’В The following image shows a screen-shot of the rotation gizmo: Works in the same way as vertex snapping, but it applies to the center and corner points of the objects'Р’В bounding box. This works in the same way as vertex-to vertex snapping, but this time the source vertex will beР’В snapped to one of the grid's cell corner points. Once you found the vertex that youР’В are interested in, press the left mouse button and move the mouse around to snap the selected objects.Р’В The objects will be snapped to the vertex which is closest to the mouse cursor. Press the V key on theР’В keyboard and then move the mouse around to select one of the vertices of the selected game objects.Р’В This is the vertex that will be snapped to the destination position. In order to use step snapping, you have to keep the CTRL buttonР’В pressed and then manipulate the gizmo as you would normally do (using the axes or the squares orР’В pressing the SHIFT key to translate along the camera right and up axes).

3DX CHAT COMMANDS MANUAL

Gizmo released a post today with an instruction manual for the World Editor

3dx chat commands